The Complete Guide to Power Tools in Saudi Arabia: Drills, Angle Grinders, and Bits Compared, with Prices
Power tools guide for Saudi contractors and homes: six sub-categories (drills, cutting and grinding, accessories and spares, workshop machines, saw blades, heat and fastening guns), leading brands, and price range and median from Almadah's catalog (VAT-inclusive, 10/11/2026).
Short answer: Power tools are portable corded or cordless machines that drill, cut, grind, and fasten. Almadah's catalog splits them into six sub-categories: Drills & Drivers, Cutting & Grinding, Accessories & Spare Parts, Workshop Machines, Saw Blades, and Heat & Fastening Guns. The category median price is SAR 61.24 including VAT (10/11/2026).
What are the six power tool sub-categories and their price ranges?
| Sub-category | What is inside | Price range (SAR) | Median (SAR) |
| Drills & Drivers | Corded and cordless drills, hammer (impact) drills, SDS drills, and angle grinders | 0.30 to 17,583.79 | 235.00 |
| Cutting & Grinding Tools | Cutting and grinding discs, angle grinders, saws, and cutting machines | 0.63 to 29,365.31 | 63.48 |
| Tool Accessories & Spare Parts | Drill bits, sockets, accessories, and spare parts (carbon brushes, springs, switches) mainly for Makita tools | 0.25 to 8,857.99 | 32.94 |
| Workshop Machines & Equipment | Air compressors, pressure washers, and heavy workshop machines | 4.00 to 157,151.57 | 679.00 |
| Saw Blades | Saw blades for wood and metal | 1.73 to 1,782.50 | 27.15 |
| Heat Guns & Fastening Tools | Heat guns and fastening guns | 41.00 to 1,031.55 | 208.15 |
Prices include 15% VAT, taken from Almadah's catalog on 10/11/2026, for published and approved products only, after any active discount. Ranges are wide because one sub-category can hold a spare part under SAR 1 next to a complete machine, and Workshop Machines reaches its upper end with large industrial compressors. Use the median, not the maximum. The whole-category median is SAR 61.24.
What is the difference between a standard drill, a hammer drill, and an SDS drill?
A standard drill only rotates and is enough for wood, metal, and soft walls. A hammer (impact) drill adds light percussion that helps in block and brick. An SDS drill hammers far harder through a dedicated bit-locking system and is the right choice for reinforced concrete, with SDS-Plus bits for medium work and SDS-Max for heavy work. A wall-type selection table is coming in a dedicated article in this cluster.
When should I choose a cordless drill over a corded one?
Choose cordless when you move between sites, work where power is unavailable, or do short intermittent jobs. Choose corded for long continuous runs at steady power with no battery to wait on. Voltage (12V, 18V, and above) sets the power, and a detailed comparison follows in a later article in this cluster.
What is an angle grinder and how do I choose its disc?
An angle grinder is a rotating tool with a swappable disc: a thin cutting disc for metal, a thicker grinding disc for removing weld and edges, and a diamond disc for concrete and tile. Common sizes are 4.5, 7, and 9 inches; larger means stronger and heavier. Before buying, match three things: disc diameter and arbor hole to the tool, the disc's rated speed against the tool's speed, and the disc type to the material. Almadah's Cutting & Grinding sub-category carries discs from Hyundai, Tyrolit, and Makita.
Which brands are most available in power tools?
Makita leads by a wide margin, and a large part of its presence comes from the Accessories & Spare Parts sub-category, which holds many individual parts for its tools. DeWalt, Hyundai, and Osco follow, with Tyrolit in discs, Bosch in drills, and Ridgid and Greenlee in technician tools. The order reflects catalog availability on 10/11/2026, not quality.
Which products have actually been ordered in this category?
Order history here is limited, so we do not claim "best sellers" in a broad sense. Products with recorded orders as of 10/11/2026: a Hyundai 4.5 inch grinding disc and a cutting disc (quantity 4 each), the Bosch GSB120-LI cordless drill (quantity 4), a Hyundai 50-litre air compressor (quantity 3), and the Makita DHP486RFJ drill (quantity 1). Many workshop and contractor purchases are placed directly rather than through the cart, so this is a partial signal only.
How do I read and compare the prices?
Compare within the same sub-category and tool type, and look at the median before the range. For example, the Drills & Drivers median is SAR 235.00, while Cutting & Grinding is SAR 63.48 because most of it is consumable discs and accessories. Prices move with suppliers and discounts, and we do not promise a fixed price.
FAQ
What are the sub-categories of Power Tools at Almadah?
Six: Drills & Drivers, Cutting & Grinding Tools, Tool Accessories & Spare Parts, Workshop Machines & Equipment, Saw Blades, and Heat Guns & Fastening Tools.
What is the difference between a standard drill, a hammer drill, and an SDS drill?
A standard drill only rotates and suits wood, metal, and soft walls. A hammer drill adds a light percussion for block and brick. An SDS drill hammers far harder and is the right tool for reinforced concrete, with SDS-Plus or SDS-Max bits.
When should I choose a cordless drill over a corded one?
Cordless for mobility, sites without power, and intermittent work. Corded for long continuous runs at steady power with no battery to charge.
What is an angle grinder and what is it used for?
A rotating tool with a swappable disc that cuts, grinds, and polishes metal, concrete, and tile depending on the disc. Common sizes are 4.5, 7, and 9 inches.
Does any disc fit any angle grinder?
No. Disc diameter and arbor hole must match the grinder, the disc's rated speed must not be lower than the tool's speed, and the disc type (cutting, grinding, or diamond) must match the material.
Which brands are available in this category?
Makita leads by a wide margin, followed by DeWalt, Hyundai, and Osco, with Tyrolit for discs and Bosch for drills.
What is the price range of power tools at Almadah?
The category median is SAR 61.24 including VAT as of 10/11/2026. The range is very wide, from under SAR 1 for a spare part to very high figures for industrial workshop machines, so compare within the same sub-category.
Can I find spare parts for Makita tools?
Yes. The accessories and spare parts sub-category holds many individual Makita parts. Check your tool's model number before ordering.
